Harbor Freight Dust Collector Impeller Upgrade
The process went quickly. Harbor Freight dust collector impeller upgrade PSA. Also, the filter bag that came with the Harbor Freight dust collector didn't filter out the tiniest particles. I went one piece at a time, figuring out the best place for the wye. 7 So if you do this realize that you are putting additional stress on the motor, which may end up in its premature death.. My unit is 8yrs old and I would be happy to replace it. Harbor freight dust collector impeller upgrade kit. 5" hole for coupler. It's also one extra step before I cut anything. The following is based on my research. I had planned for double pickups at a few tools. Super simple process and by far the easiest upgrade. The filter has worm gear straps that attach from the dust collector body to the filter. Even with a split, suction from both pipes wasn't cut in half.
- Harbor freight dust collector impeller upgrades
- Harbor freight dust collector impeller upgrade your browser
- Harbor freight dust collector impeller upgrade today
- Harbor freight dust collector impeller upgrade kit
- Harbor freight dust collector impeller upgrade your flash player
Harbor Freight Dust Collector Impeller Upgrades
I screwed it on one side in case I ever need to remove the gate or if the fit becomes an issue and I need to sand it down, I have that option. How We Upgraded a Harbor Freight Dust Collector. I am very happy thus far.
Harbor Freight Dust Collector Impeller Upgrade Your Browser
To dump the trash can, I bolted 3/4" plywood to the smallest scissor jack I had on hand. This proved an effective adapter. With my pipe brackets, everything stays in place. I used EVA foam to fill the gaps from the 2. Make sure that if you use masonry anchors, the screws are long enough to fully engage the anchor. Harbor Freight Dust Collector Build. It just wasn't cutting it so I modified it with a larger impeller so that I could use a six inch duct. So, like many, I have the 2HP Harbor Freight Dust collector, upgraded to a Wynn 35A filter. It snapped trying to fit it to a 17" diameter. I made a U bracket out of 2x4s to hold the filter in place against the wall. What I really like about the Super Dust Deputy XL Cyclone Separator is it separates the wood chips and the dust so only air and very fine particles pass through the blower to the filter. I also created a port on the band saw. From the research it has the same shaft diameter as the harbor freight one and is a direct bolt in. At any 90* turns you want to use two 45s and a straight run of pipe instead of a 90* elbow.
Harbor Freight Dust Collector Impeller Upgrade Today
Easy enough, but the output is still necked down to 5" isn't it? FYI this makes a lot of noise in metal ducting. I was also excited to attach the ONEIDA Dust Sentry Level Sensor. A total of 8 srews holding it on. Removing impeller form Harbor Freight DC - General Woodworking. I'm just wondering if anyone has built their own impeller for the HF dust collector and what kind of success or failure they had or if there were any lessons learned to be shared? I have a few tools that have 4" dust connectors and I don't think my shop vac is cutting it anymore. If you don't have any big pieces of equipment like a table saw you may not need a separate circuit, but if you are using handheld equipment it's unlikely you would be installing dust collection anyway. My thought process here is to go with 6" mains, and keep my 4" branches / blast gates. I have a Harbor Freight "2HP" dust collector. While you can buy trash can tops that mimic the design and some designs have the baffle completely inside the trash can, I wanted the PVC pipe to run straight into the baffle with no 90* turns.
Harbor Freight Dust Collector Impeller Upgrade Kit
1/2″ Sheet Metal Screws. In lieu of the Wynn filter, the Donaldson P181038 filter is reported to be a direct equivalent to the Wynn 35a with a much lower price tag. Using a 3 jaw puller, CAREFULLY attach the puller to the flange lip of the stock impeller. I linked the Wynn clips. Dust collector upgrade thoughts. It's a 12" impeller with reverse vanes while the stock HF impeller is 10" with forward vanes. The next step was to remove the woodruff key from the old impeller and put it in the new one. The plywood is cut round with a 1/4" channel for the trash can bottom edge to sit into for stability. I was concerned that painting the blades could cause them to swell slightly and I didn't want to have to re-sand them. I made the rough cuts a bit wider than necessary to leave room for the router to trim. This trash can has a 17" inner clear diameter. Remove the original bag filter, and support bar.
Harbor Freight Dust Collector Impeller Upgrade Your Flash Player
Align the new impeller bore / keyway to the key / shaft, and wiggle it a bit until it just barely starts to go in. I selected 4" PVC pipe due to cost and availability. It was a slow cutting process. Any branches need to be wyes, not tees. Noise dropped by 3db to 93 db at 3 feet and 87 db at 6 feet.
I was finding it was inconvenient because I was constantly having to unhook it from my table saw and then wheel it across the room to hook it up to my miter saw and then unhook it from my miter saw and wheel it back across the garage to the table saw. I was going to split the pipe to collect from the base and top of the router table, but didn't have the space. The circle cutting jig made cutting the curves very easy while ensuring the top and bottom were exactly the same size. After coming up short, it seems a 1. You want to stop any air leakage to maximize efficiency. I used a hobby knife to cut through the vinyl of the flex pipe, make sure my start and end of the cut ended on the same wire support. Gray House Studio does receive commissions for sales from these links but at no extra cost to you. Harbor freight dust collector impeller upgrade your flash player. Since I was doing electrical work in the shop at that point anyway, it wasn't a major issue. One of the big things I learned midway in this project is that if you're adding dust collection, chances are you will need to put it on a separate breaker.
That dictated the trash can height which would needed a 10. Prior to last upgrade. The bag will catch any particles that makes it though the blower to the filter. Harbor freight dust collector impeller upgrades. Using a jigsaw and sheet metal blade the intake port was widened from 5″ to 6″. I considered attaching springs to hold the baffle to the trash can, hooking to the can's handles and drilling a hole into the bottom plate. I didn't want to create any kind of ledge to catch dust so the sides extend the depth of the slot. Rivet Gun with 40-Piece Rivets. Had it hooked to a few tools with hoses & the stock bag, which is like a big pillow case.
Each sawdust producing piece of equipment is connected to the impeller through pipes. I've watched several videos, particularly from Matthias Wandel, regarding shop-built impellers. I used masonry anchors to attached 3/4" plywood to the wall to mount the motor. I bought longer screws as the ones that came with the anchors weren't long enough to go through the plywood and fully engage the anchor. Not sure if I will paint or not, but the initial feel is good & I'll know better once it's hooked up, I did notice it is a little quieter, maybe the air filter vs bag??? I have no issues with 2, 4" lines at once.
Unfortunately I don't have a lot to put towards something, but does anyone have any suggestions for a minor step up? So, I started the upgrade by removing the 5″ DC hose and the connections at both sides. My pipe height was dictated by counters. I sketched a shape across (2) 2x4s and then cut them out on a band saw. The Thien baffle hangs from the motor, I used scrap metal channel and threaded rod to create a clamp. The baffle is roughly the same.