Toyota Sienna Sliding Door Won't Open
HOW TO REPLACE/REPAIR SLIDING DOOR CABLE ON A TOYOTA SIENNA 04 05 06 07 08 09 10. 2007 Toyota Sienna Sliding Door Repair. Doing so will keep clumps of mess and grease collecting in the assembly. The 5th picture shows the cutout piece of the latch. I just came back from Dealer, They tell me it's a motor. 4th Step: Lubricate. How To Fix A Power Slide Door That Won't Open Properly On A 2004 - 2010 Toyota Sienna The Cheap Way. Toyota sienna sliding door won't open in a new window. They did however replace the cable in the one sliding door. According to NHTSA, "the remedy for this recall is still under development. Try pulling the handle to open the sliding door.
Don't forget to get a clean towel to wipe off the excess lubricant. How to repair Toyota Sienna Sliding Door. Quick Fix for the Rollers. Step 1: Symptom of Sliding Door Latch Problem. If you are not confident that you can do this on your own, you can bring your HiAce van to an expert mechanic. Toyota sienna sliding door won'to open in a new. This will fix the problem. But if you pull the handle and hold it for a few seconds the door opens. We have to drive to school about 20 min). I have searched the internet and YouTube to find out how to fix my Toyota Sienna XLE 2006 sliding door problem.
To do that, you need to follow these steps: 1st Step: Deal with the Tailgate. The bad news is you can't just get this part, you need the whole latch assembly which you can get for about $130ish on ebay. It is possible that there is an issue with the rear rollers in your HiAce van's sliding door. I used a hot glue (7th picture) to glue the cutout piece (5th picture) back to the latch. Toyota is still working on a fix and anticipates notifying owners of the problem in mid-January. Once you've done that, you can now put the assembly back together. Sounds like the power slider latch assembly or track have gone bad. Introduction: Fix Toyota Sienna (or Any Car) Power Sliding Door the Fastest and Cheapest Way. By the way I am a semiconductor engineer and not a mechanics. You can use the PEX tubing to create your own bushings. I saw on YouTube people struggled with removing the latch unit.
When it gets to the end of the open sequence, it can be closed without any resistance - if that makes sense. Make sure you do not damage the paint and the pin. Keep in mind that they won't work the same as the old ones. If you're not familiar with this product, you can ask your local auto parts shop for the material used for potable water systems on RVs.
I had this problem a few times and what I found was that it was the rubber piece on the side of the door that had come part way off and was not able to close al the way even though it was an inch from closing. A quick fix for this is using PEX tubing. 3rd Step: Clean the Assembly. They fit tightly, allowing even the worn pins to grab onto the pipe securely. The door is supposed to unlatch first before it triggers the motor to pull it open. Showed it to mechanic, he said all do it. Be careful not to drop the bolt, but if you do, you can retrieve it using a magnetic tool. Sharing buttons: Transcript. Owners may contact Toyota customer service at 1-800-331-4331. This didn't happen last year. Can it be replaced by the owner? You can hear the motor but it does not pull the door in to latch.
I'd take this to the dealer. The kids have to climb over the front seat. Some used Hiace vans for sale can have sliding doors that are stuck. Throughout the day, several people slide the door open and close, handling it differently. The Problem: According to the National Highway Traffic Safety Administration, if the power sliding door is unable to be opened when commanded, such as if the door is frozen shut, the door may subsequently open unexpectedly, possibly while the vehicle is moving. I got a new replacement battery, and now the door closes properly. They were time consuming, high risk, and more expensive. I know this is old, but I have the answer so figured I would post so others can see. Lift it up, then use a flat head screwdriver to remove the screw coverings. Could they have broken a seal or something that's somehow causing moisture to get into the car and freeze up the doors?
Close the sliding door of your Hiace van. After lubricating the assembly, try opening and closing the sliding door several times. Problem: The sliding door latch is not working (see the picture of the latch unit). Just got this last year, bought it CPO with 28, 000 miles. Yes it's old turkey pig but the problem is older, your suggestion is probably correct, I've tried replacing rollers with 10 cent nylons, but they wear quick and aren't exact, now gonna order psd assembly and make sure they are lined up, than it may be the latch assembly next, these doors need a recall.
Open the sliding doors, then use the inline socket to remove the bolt in front of the track's cover. If you hear the motor working and hear a metal to metal sound then the cable in the latch assembly has broken apart. If I get down close to the bottom of the door near track, I hear a slight metal to metal grinding sound. Power sliding door will not latch.
70 after tax and shipping in Minnesota) each door and it took me less than an hour, seriously!!! Details: Driver's side door opens automatically from any button, appropriately. If it only makes some sound without opening the door, then there must be something wrong with the latch. Step 3: Replace the Motor of the Latch. Gently slide a soft cloth over the cable and track.
I used a rotary tool (1st picture) to cut open the latch where the motor was (2nd picture, red circle where the motor is).