1St Gen Tacoma Lower Ball Joint Torque Specs

When purchasing OEM LBJs, you have several choices on a 1st gen 4WD Tacoma (or Prerunner). And torque the endlink nuts to 22 ft-lbs and then torque the bracket bolts to 19 ft-lbs as well. Shift lever retainer: 29 ft-lbs (2RZ/3RZ), 13 ft-lbs (5VZ). Hey Jordan, there are some pics of the bolts in the Prado 90 Series forum link I provided, if that helps.

• 1st gen tacoma lower ball joint torque specs reviews
• 1st gen tacoma lower ball joint torque specs pictures
• 1st gen tacoma lower ball joint torque specs images
• 1st gen tacoma lower ball joint torque specs and gear

1St Gen Tacoma Lower Ball Joint Torque Specs Reviews

In an instance where you receive a damaged package a claim must be made with Dirt King Fabrication. Frequently Asked Questions. This time, it's been 15 months, and it's definitely time for replacement. The easiest way to do this is to loosen up the 2 bolts which hold the brake caliper bracket. 1993 Corolla Wagon 7AFE.

The upper ball joint only has one fastener that holds the ball joint onto the upper control arm. To start remove the center axle nut from the center of the hub. Guides are intended to assist in each procedure to help diyers with the job. Throttle body mounting nuts/studs: 13 ft-lbs. I'll even throw in four bolts, a couple castle nuts, and one cotter pin for the same low, low price!

1St Gen Tacoma Lower Ball Joint Torque Specs Pictures

Carrier bearing caps: 83 ft-lbs (w/o e-locker). In order to be replaced. Bolts and nut tork spec. Once the tire is off you can now access the old tie rod and remove it for replacement. "Green" Flange Head LBJ Bolt (90105-10406). Damaged or Missing Parts. Our suspension systems are not to be modified from its original design in any way. Engine mount to block: 38 ft-lbs (2RZ/3RZ), 32 ft-lbs (5VZ). But, a ton of us have achieved the 59 ft-lbf torque value with no issues so that theory might not really hold weight. Milwaukee mid-torque impact wrench. Flywheel to crankshaft bolts: 65 ft-lbs (2RZ), 19 ft-lbs + additional 90 (3RZ), 63 ft-lbs (5VZ) ~USE LOCTITE~. Once the bolts have been removed you can take off the hub. 1ST Gen Suspension Torque Specifications. 4 bolts that hold it in place. As these are removed the shock will separate from the vehicle and.

Ring gear bolts: 71 ft-lbs. Flexplate to crankshaft bolts: 54 ft-lbs (2RZ/3RZ), 61 ft-lbs (5VZ). Guys, this is a great discussion. Suspension/Steering. Starting with the lower bolt we simply remove the nut from one side and then. Mechanical engineering at this level isn't always intuitively obvious. Torque specs for 05 double cab 2wd. Lower ball joint nut. Unlike the Tacoma, there's really only one choice of LBJ for the 4Runner, making things easy. 95-04 Toyota Tacoma torque specs (Prerunner/4x4). Differential rear mount to frame: 64 ft-lbs. Pressure plate to flywheel: 14 ft-lbs. Returns are only accepted within 30 days of receiving the product. Another idea no one has mentioned yet is to replace the bolts with high strength studs and flange nuts. When I replaced my LBJs about 2 yrs ago, I torqued them to 37ftlbs with blue threadlock.

1St Gen Tacoma Lower Ball Joint Torque Specs Images

This is great information. Ring gear bolts: 71 ft-lbs (with e-locker), 92 ft-lbs (w/o e-locker). '89 Camry Alltrac LE 3S-GTE 5spd. Differential drain & fill plugs: 36 ft-lbs. Customer assumes all liability in assuring that parts are correctly installed and maintained. To install the new wheel hub you must first remove the old hub from the vehicle. Just bought a new set of ball joint bolts (90080-10066) to make sure I got these torqued to the correct number when I replaced them a few years back. Before you can access these bolts you will need to jack the vehicle up and remove the. Dirt King Fabrication ships their products within the United States and Internationally. Just joined the list of people with failed lower ball joint bolts. Just now going to bed at 7AM thanks to this little SNAFU. Driveshaft center support bearing: 134 ft-lbs to set, then loosen, then 51 ft-lbs. Nut that holds the lower arm to the knuckle. But then it becomes a game of not getting them so tight the knuckle gets stripped. Spark plug: 14 ft-lbs (2RZ/3RZ), 13 ft-lbs (5VZ).

Inner tie-rod to rack: 76 ft-lbs. The older ones must be stronger thus the higher torque value. I'm beginning to wonder if it makes sense to move to something like an ARP bolt in the LBJ for the dramatically increased tensile strength. 1st gen tacoma lower ball joint torque specs and gear. The old bearing can be removed by taking out the. Axle shaft inner hub safety bolt (manual hubs): 13 ft-lbs. If you do have a rubber dust covers on your LBJs, you need eight (8) of "black" (washer) bolts.

1St Gen Tacoma Lower Ball Joint Torque Specs And Gear

Note: this is 19mm castle nut on a 4Runner. This helps to avoid. Been removed you can place the new one in and begin to tighten down the 4 bolts. There should be 3 nut in total. Stud spins in steering knuckle. E-locker acutuator to 3rd member: 20 ft-lbs. Driveshaft center support bushing to frame: 27 ft-lbs. 1st gen tacoma lower ball joint torque specs pictures. Torque Values for Lower Balljoint Bolts - Very Important - Please Read. Main bearing caps: 29 ft-lbs + additional 90 (2RZ/3RZ), 45 ft-lbs + additional 90 (5VZ). I know they chose a longer bolt due to the dust covers on the 01 and 02 models but why didn't they spec a bolt with the same tensile strength as the other bolts. Previous: '88 Camry Alltrac LE 3S-GE BEAMS, 90 Camry 3S-GTE, 90 Camry DX, '03 WRX wagon, '08 Outback XT. The customer must be present for the delivery to inspect and sign for the package. I wonder why the change?

Communicate privately with other Tundra owners from around the world. To install a new tie rod on a Toyota Tacoma you must first remove the old one from the vehicle. 1st gen tacoma lower ball joint torque specs images. There is a bit of corrosion holding the hub in place. Companion flange nut to transfer output shaft: 87 ft-lbs. Hey, anyone interested in purchasing some low-mileage, never-seen-dirt, OEM lower ball joints for a great price before they go on Craigslist as "like new"? The lower ball joint nut gets tightened down. 2000 SR-5 Highlander version 4:30's, factory locker, green, bought 6/21.